We fabricate and install glass shower doors in Homer Glen. Frameless enclosures, semi-frameless doors, sliding glass panels, and cut-to-size mirrors. Glass is the only trade we work in.

Homer Glen developed differently from its neighbors. The village only incorporated in 2001, and much of what is here was built on large parcels with wide setbacks, which produced bigger houses on bigger lots than you find closer to the city. Primary baths reflect that, frequently with a separate tub and shower, a walk-in with multiple panels, and a double vanity spanning most of a wall.

Bigger does not mean simpler. More panels means more pieces that have to meet correctly, and larger spans require thicker glass. We template each opening in the room before anything gets cut.

We measure, fabricate, and install frameless and semi-frameless glass shower doors, sliding enclosures, custom panels, and oversized mirrors for homes throughout Homer Glen and the surrounding Will County suburbs.

A double vanity in a Homer Glen primary bath commonly runs seven or eight feet wide. Stock mirrors do not come in that size, which leaves homeowners choosing between one that looks undersized and two that fight with the sconce placement.

We cut to the actual wall instead. The measurement has to account for the light fixture, the backsplash height, any tile edge, and outlets in the field. Where a single sheet would be impractical to move or mount, we seam it and show you where the seams land before fabrication.

• Mirrors cut to the real vanity width, not a catalog size
• Cutouts and notches for sconces, outlets, and switches
• Measured on the same visit as the shower enclosure where scheduling allows

People assume a large bathroom is an easier glass job. In practice the opposite is true.

Weight is the first reason. Glass thickness is a structural decision, not a style preference, and a panel spanning a wider opening carries more of its own load. Half-inch glass becomes necessary where three-eighths would have been fine at a smaller size, and a half-inch panel of real dimension can exceed a hundred pounds. All of that transfers into the wall through a small number of hinges, so anchoring into studs or blocking is not optional.

Complexity is the second. A walk-in with a fixed panel, a door, and a return is three separately templated pieces that have to meet each other at the seams. Add a bench interrupting the panel line and there is a fourth variable. None of it can be adjusted once tempered, which is why we measure each piece individually rather than working from a single overall dimension.

Enclosures installed during Homer Glen’s main building period are now old enough that hardware starts needing attention, and heavy frameless panels show it first.

The usual pattern: a hinge drifts under sustained weight and the door begins sitting low at one corner, or a clamp loosens and the panel shifts slightly out of square. Both are correctable, and both are cheaper to address early, because a panel hanging out of alignment puts uneven stress on the remaining hardware. We also handle sweeps that hardened and now let water past, loose handles, and single-panel glass replacement where the frame and anchoring are sound.

Where we advise replacing is when anchoring has pulled out and damaged the substrate, or when hardware from a discontinued line cannot be sourced. On a heavy frameless enclosure the second problem matters more than most people expect, since improvised hardware is carrying real weight.

Custom shower doors start at $999, though Homer Glen projects frequently land above that because of scale. Glass thickness is a primary driver, since larger panels require half-inch rather than three-eighths. Panel count matters just as much, as a walk-in with a fixed panel, a door, and a return is three fabricated pieces instead of one. Hardware finish and edgework add to the figure, and oversized mirrors are priced separately by square footage and edge treatment. Secondary and guest baths with sliding or semi-frameless enclosures sit closer to the entry point. You get one firm written number after the on-site template.

Call and we schedule a free on-site visit to your Homer Glen home. We template each panel individually, confirm the walls can carry the glass weight, and talk through thickness, hardware finish, and edgework. If you want the vanity mirror handled at the same time, we measure that on the same visit.

Once you approve the quote, the glass goes into fabrication cut to that template. We call to schedule installation when it is ready. Our crew sets and levels each panel, seals the perimeter, removes the old enclosure if there is one, and walks the finished work with you. Silicone has to cure before the shower is used, and we tell you exactly how long to wait.