We fabricate and install glass shower doors in Orland Park. Frameless enclosures, semi-frameless doors, sliding glass panels, and cut-to-size mirrors. Glass is the only trade we work in.

Orland Park grew in stages, and the bathrooms show it. The older sections near the historic downtown and along the Metra line have compact baths with standard tub alcoves. The subdivisions that filled in from the 1980s through the 2000s have larger primary suites, often with a corner shower set at an angle or a separate tub and shower arrangement.

Different eras, same requirement. We template the opening in your bathroom and cut the glass to it, because tempered glass cannot be adjusted once it is made.

We measure, fabricate, and install frameless, semi-frameless, and sliding glass shower doors, custom enclosures, and mirrors for homes throughout Orland Park and the surrounding southwest suburbs.

Builders working through Orland Park’s growth years used the corner shower constantly. Setting the unit at forty-five degrees saves floor space in a primary bath and it looks good on a plan. What it produces is an enclosure needing three panels meeting at two angles, and those angles rarely match the drawing.

We template each panel and each angle individually before anything is cut. There is no trimming a tempered panel afterward, so a neo-angle enclosure either fits the corner as built or it gets refabricated.

• Every panel and angle measured individually in the room
• Glass cut to the corner as constructed, not as drawn
• Hardware laid out around where the studs actually sit

Measuring bathrooms across Orland Park means giving genuinely different advice depending on which part of the village you are in.

In the older sections, the tub alcoves were framed decades ago and have settled since. Openings taper from ceiling to floor, and plenty of these bathrooms have had tile laid over the original tile, shifting the dimension again. Semi-frameless glass shower doors usually perform better there, because the perimeter framing spans variance that a frameless panel cannot absorb.

In the newer subdivisions, the walls run true and the constraint becomes complexity rather than settling. Corner units set at an angle, benches cutting into the panel line, walk-in showers with a fixed panel and a return. Frameless is entirely viable, but there are more pieces meeting each other and no margin to adjust any of them once tempered.

Which situation your home falls into decides the honest recommendation, and you get it at the template rather than after the quote is signed.

Enclosures installed during Orland Park’s biggest building years are now two to three decades old, which is when hardware starts asking for attention.

The common calls: hinges that drifted and let a heavy frameless panel sit low at one corner, clamps that loosened, sweeps that hardened and now let water past onto the tile, handles pulling loose from the mount. On sliding units in secondary baths it is almost always rollers and tracks packed with hard water buildup.

All of that is repairable at a fraction of replacement cost, and addressing it early matters, because a panel hanging out of alignment puts uneven stress on the remaining hardware. What is not worth patching is anchoring that has pulled out of the wall, or hardware from a discontinued line where parts cannot be sourced. You will hear which situation you are in before spending anything.

Custom shower doors start at $999. Glass thickness, hardware finish, and the complexity of the opening determine the final figure. Sliding glass shower doors and semi-frameless enclosures over a standard tub alcove sit at that entry point, which covers most hall and secondary baths in the village. Frameless costs more because the glass is thicker and the hardware carries the full panel weight. The configurations common in Orland Park primary suites cost the most, since corner and neo-angle enclosures, walk-in panels with returns, and cuts around benches all take more glass and more precise fabrication. You get one firm written number after the on-site template.

Call and we schedule a free on-site measurement at your Orland Park home. We template the opening, measure each panel and angle where the shower is a corner unit, confirm where the hardware can anchor, and talk through glass thickness, finish, and edgework.

Once you approve the quote, your glass goes into fabrication cut to that template. We call to schedule installation when it is ready. Our crew sets and levels the panels, seals the perimeter, removes the old enclosure, and walks the finished shower with you. Silicone needs to cure before the shower gets used, and we give you the exact wait time.